eTWIN PH-RX Dual Dispenser
ETWIN PH-RX double pump dispenser.
ETWIN PH /RX "FULL" Package Contents(complete set, ready for installation):
1 PC. - eTWIN PH-RX 2-6 (5-5) 230V PVDF pump
2 pcs. - reagent injection valve 3/8 "- 1/2" PVDF
2 pcs. - PVDF reagent intake valve - Viton, with remote control
(with integrated reagent level sensor)
2 pcs. - 4x6 PE reagent supply hose (matt), 2 m
2 pcs. - 4x6 PVC fence hose (transparent), 4 m
Of these, it is used:
2 r.m. - for collecting the reagent;
2 r.m. - for the air bleed valve
1 PC. - PH level sensor with 5 m cable.
1 PC. - RX level sensor with 5 m cable.
1 PC. - calibration solution PH 7, 55ML
1 PC. - calibration solution PH 9, 55ML
1 PC. - calibration solution 650 mV, 55ML
2 pcs. - sensor holder 1/2 ", IN-LINE, PP
4 things. - clamping saddle DN50 - GF1 /2 ", PP
1 PC. - wall mounting platform for the pump
1 PC. - a set of dowels and screws for fastening
1 PC. - passport-instructions for installation and maintenance
1 PC. - warranty card
The main advantages and technical capabilities of eTWIN PH /RX FULL:
- ETWIN is based on two new generation diaphragm metering pumps with a PVDF flow end, an integrated controller for measuring the pH level and Redox, which are integrated into a single compact housing, measuring 270x235x148 mm.
- Fully Russified menu, I include a built-in system of prompts for the operator
- PH Priority function - an effective software function to achieve savings in the consumption of dosed chemicals in the swimming pool
- Pump capacity depending on the selected model: 2 l /h - 6 bar or 5 l /h - 5 bar
- Measurement ranges: 0-14 pH; Rx: -1000 ÷ + 1400 mV; 0-100 ° C
- Proportional dosing - set by default
- Manual dosing mode
- Dosing Pump Pre-Injection Procedure
- Function: Password - is used to set protection "against access by third parties" for individual sections of the menu: SET POINT, CALIBRATION, SETTINGS and in PAUSE mode
- Programmable time for setting the start delay of the metering pumps, independently for each measured parameter
- Automatic diagnostic system for pH and Rx sensors during the calibration procedure
- Flow sensor support (for all or selected measured parameter)
- Reagent level sensor support (joint or separate operation mode)
- PT100 temperature sensor support
- Level sensors are already integrated in the chemical intake valves, which are included with the pump
- Configurable alarms for level and flow sensors
- Alarm for minimum and maximum thresholds
- Overdose alarm - overdose on time
- Relay output for alarm
- Clock, timer (daily /weekly)
- Analog output, 4-20 mA
- Programmable non-contact relay outputs ON /OFF for measured parameters
- Programmable relay output for connecting any external actuators by timer (for example, for dosing flocculant, algicide or for flushing the HYCHLOR chlorine sensor (SCLO 3) by time)
- Dust and moisture protection class: IP65
| vendor code | Name | Back pressure performance | Flow part: Pump head | ||
|---|---|---|---|---|---|
| l / h | bar | Execution | A type | ||
| CXB8010151ER | ETWIN PH /RX 2-6 230V PVDF Pump |
|
|
PVDF-Ceramic | H |
| CXB8011151ER | ETWIN PH /RX 5-5 230V PVDF Pump |
|
|
PVDF-Ceramic | H |
