Automatic Water Disinfection Systems - POOL GUARD 3 PH/CL (SCLO3 HYCHLOR)
.jpg)
POOL GUARD 3 PH /CL (SCLO 3 HYCHLOR) is an automatic proportional dosing and control system for PH and CL levels (concentration of free chlorine in water) for swimming pools up to 500 m3. The dosing station is controlled by a liquid flow sensor (included in the kit); if there is no flow, the system goes into standby mode.
Automatic water treatment station Pool Guard 3 PH /Cl - carries out water treatment of the pool by: measuring and regulating the free chlorine indicator (inorganic chlorine only) - dosing chlorine, measuring and adjusting the pH indicator, measuring the water flow to turn off the outputs in case of absence flow. The temperature sensor (PT100) allows the controller to automatically take into account temperature compensation.
Dosing system POOL GUARD 3 PH /CL (SCLO 3 HYCHLOR) is supplied mounted on a chemically resistant plastic panel (450x600x8 mm), in a complete set, ready for installation and commissioning.
The station is equipped with two interconnected diaphragm pumps (DLX PH-RX-CL /MB 5-7 230V) with built-in pH /Rx /Cl controllers. The pumps are equipped with a graphic TFT-display with 3 LEDs (power supply, pulse frequency, level sensor signaling or alarms) and non-volatile memory, reagent level and flow control is built-in. Data entry and control is carried out using 5 control buttons on the front of the pumps. All main probes and sensors are installed in the SCLO 3 HYCHLOR flowcell. A connecting cable with an adapter is used to connect the chlorine sensor to the DLX (B) PH-RX-Cl /MB (M) series metering pump.
SPECIFICATIONS:
- The system is based on DLX PH-RX-CL /M dosing pumps with built-in pH /Rx /Cl controllers (optional) and SCLO 3 HYCHLOR flow-through amperometric free chlorine sensor.
- Alarm for continuous dosing time, followed by shutdown of dosing pumps.
- Dosing delay when the system is turned on.
- Level sensor or flow sensor alarm.
- Setting the alarm for the concentration limits of pH / Cl levels (MIN / MAX).
- Dosing modes: constant ON / OFF and proportional PROP.
- Fine-tuning the proportional mode.
- Locking the settings made by password.
- Menu selection: Basic / Full.
- Setting the hysteresis.
- Pump capacity: 5 l / h - 7 bar.
- Measurement ranges: 0-14 pH; 0-5 ppm (mg /L).
- Protection class (pumps): IP65.
- Support for flow sensor and reagent level sensor.
DOSING SYSTEM CONFIGURATION: (SCLO 3 HYCHLOR) - with SCLO 3 HYCHLOR amperometric free chlorine sensor (inorganic chlorine only).
Built-in functions:
- Alarm for continuous dosing time, followed by shutdown of dosing pumps.
- Dosing delay when turning on the station.
- Alarm and shutdown of the station by flow sensors or reagent level in canisters.
- Alarm setting for chemical concentration limits reagents pH / Cl (MIN / MAX levels).
- Dosing modes: constant "ON / OFF" and proportional "PROP".
- Setting the hysteresis.
- The dosing station is controlled by a liquid flow sensor (included in the kit), if there is no flow, the system goes into standby mode "STAND BY", followed by indication on the LCD displays of the pumps.
Inputs / Outputs:
- pH / RX inputs - BNC connectors, input impedance> 10 ^ 12 Ω.
- Cl input - 4-pin connector.
- 2 inputs "LEV" for level sensor SPDT contact 5 V / 5 mA.
- Input "FLOW" of the flow sensor (SPDT pin 5 V / 5 mA).
- Output 4-20 mA.
- Relay output ON / OFF for alarm.
POOL GUARD 3 PH /CL dosing system composition [SCLO HYCHLOR]
2 pcs. - pump DLX PH-RX-CL /M 5-7 230V PVDF
1 PC. - PH level sensor with 0.5 m cable.
1 PC. - chlorine sensor SCLO 3 HYCHLOR
1 PC. - cable with adapter for SCLO 3 HYCHLOR chlorine sensor
2 pcs. - reagent level sensor with 2 m cable.
1 PC. - mounting kit for SCLO 3 HYCHLOR chlorine sensor
1 PC. - a set of instructions for installation and maintenance
1 PC. - calibration solution PH 7, 55ML
1 PC. - calibration solution PH 9, 55ML
2 pcs. - reagent injection valve
2 pcs. - reagent intake valve
2 pcs. - reagent intake hose, 4x6, PVC, 2 lm
2 pcs. - reagent discharge hose, 4x6, PE, 2 lm
1 PC. - mounting panel 450x600x8 mm
| vendor code | Name | Characteristic |
|---|---|---|
| QPA7Q10127ER | Dosing system POOL GUARD 3 PH /CL | pH: 5 l / h; Cl: 5 l / h |
